TechMod :  The Roadbook Collection
 
Roadbooks are an interesting subject with a lot of discussion. It's a device where you can put in the tourride description and only shows the most relevant part. In most cases 3 or 4 lines visual is more than enough. We have seen many roadbooks in the past years, some bought but most of them build by the owners themselves. We have seen stainless steel but als nice transparent tubes of plexiglass, with and with builtin light. As the subject returns several times a year and people want to see samples, we have decided to start the Roadbook Collection pages. Were possible we will try to give an englisg translation. If you see Dutch text, the translation will follow soon. When we mention companies, it's possible that these are not available at your country.

Ben Baaijens roadbook solution (Halfords version)  
Ben Baaijens wrote: This solution does his job for more than 4 years, first on my XJ900 and now on my Diversion XJ900S. Buy at Halfords a route-roll for on the bike. For older people, there is also a reading ruler available, works perfect! Buy at Hein Gericke two mirror supports with M10 fine thread (watch the steer bore). Buy or get some piece of 20 cm heating pipe with a diameter of 28 mm. Buy or get two M10*100 bolts with 4 nuts. Click for more details
Make normal M10 thread in the mirror supports if you don't have fine thread. Drill 10 mm holes in the heating pipe in the middle in such a way that the mirror supports will fit between the steer clips on the steering-head. Do not drill thru! Remove the heads of the bolts and place on nut on the thread-end. Put the other M10 nut into the tube for the drilled hole and fix it. Click for more details
Put the mirror supports on the other end and mount the whole on the steer. Put some tape on the ends of the heating pipe to make it somewhat less slippery. Click the Halfords route-roll on it and the tour can start! Click for more details
Note editor: Do not fix the mirror support so much that you cannot move it. Remember that in case you have a frontal crash, you should fly over your steer. The plastic screws of your windshield are supposed to break for your free flight. The roadbook construction should in this case not stop you but slide forwards down. Click for more details

Pim Beijen's route scroller (Pan version)  
Pim Beijen wrote: First I would like to recommend to install a flexible route scroller on your motorbike as this improves the safety of driving but above all helps you enjoying driving. Due to my recent move to Denmark I had to sell my Honda Pan European due to very high so called ‘registration tax’. I still had an ‘old’ route scroller from my ST1100. Due to the heavy tax in Denmark I bought a Diversion XJ900s.
The original route scroller is actually built for a pushbike (typical Dutch !), but is adjusted for the use on a Pan European motorbike. As far as I know this is only for sale in Holland at the Pan European club or at one motor shop called Vos in Oss (close to Den Bosch). This adjusted version already has two aluminium tubes at the end including a bolt and nut (picture 1). Click for more details
Looking at the possibilities for the Diversion I saw that I only needed to bow a small iron plate at both sides that could fit on the mirror rod. I went to the DIY and bought two iron plates (garden supplies) of 2mm thick, by 2cm wide and approx. 8cm long (cost € 1,30), as well as two rubber rings (cost € 0,50) (picture 1). Click for more details
The only thing I did than was to bow the plates simultaneously in a bench vice, total time approx. 20 min. As pictures 2 and 3 show one angle is at 45 degrees and the other at 90 degrees. As the iron plates already had holes I had to drill the lower hole at 10mm to fit in the mirror rod. Click for more details
The upper hole had to be sawed from the top in order for the route scroller to fit in. When you install the iron plates on the mirror rods you only have to adjust them so the route scroller is in a horizontal position (pictures 4 and 5). The mirrors are not at the same position on the steer, therefore this adjustment has to be made. Click for more details
I included rubber rings to make sure that the scroller can be completely tightened and can not get loose when driving. In total I needed about one hour to think about the solution, execute it and in the meantime buy a 10mm gimlet, so if you know what you need you can do it in relatively short time. Good luck and much pleasure in driving. Pim Beijen Click for more details

Marcel Hudepohl's roadbook  
Marcel Hudepohl's roadbook we saw when he sold in some time ago thru the YDCN website. This roadbook is made of stainless steel, aluminum and lexaan cover. Click for more details

Leo Schelvis A4 routereader  
Leo Schelvis from Almere in the Netherlands sent us the following low budget solution. Take an A4 sized plate of aluminium and an A4 sized plate of plexiglass. Connect them with a hinge at the top. Click for more details
Just checking... ok, an A4 sized YDCN route description will fit Click for more details
To get this plat mounted on the stear, a mount of a pushbike lock has been used. Click for more details
The final result, seen from the right side Click for more details
And the final result seen from the drivers seat. There is hardly any vibration but the whole isn't waterproof. Click for more details

Various  
Piece of cardboard and a piece of string Click for more details
Brand and supplier unknown but probably a normal route roller for the push-bike Click for more details
Same routeroller from a different angle Click for more details

Last update 12-Aug-2012